精品视频一区二区三区在线观看-精品视频一区二区三区在线播放-精品视频一区二区观看-精品视频亚洲-青青青国产在线-青青青国产依人在在线观看高

鄂式破碎機主要用于對各種礦石或大塊物料進行中等粒度的破碎。按照進料口寬度大小來分為大、中、小型三種，進料口寬度大于600mm的為大型機，進料口寬度在300-600mm的為中型機，進料口寬度小于300mm的為小型機。顎式破碎機（簡稱：鄂破）廣泛應用于礦山、冶煉、建材、公路、鐵路、水利和化工等行業。被破碎物料的最高抗壓強度為320Mpa。

Jaw Crusher is mainly used to crush various medium particle size of ores or large materials. According to the feed inlet width, it can be divided into three types: large, medium and small. Large machines are those with a feeding width over 600mm; medium machines are those with a feeding width of 300-600mm; small machines are those with a feeding width smaller than 300mm. Jaw Crusher (abbreviated as J Crusher) is widely used in mine, metallurgy, building, material, highway, rail way, hydraulic engineering and chemical industry, etc. The maximum compressive resistance of the crushed materials is 320Mpa.

技術優勢和特點/ TECHNICAL ADVANTAGES AND CHARACTERISTICS

●其破碎比大，產品粒度均勻；破碎腔深而且無死區，提高了進料能力與產量；

The crushing ratio is big with a uniform product granularity; the crushing cavity is deep with no dead zone, thus improving the feeding capacity and output;

●墊片式排料口調整裝置，可靠方便，調節范圍大，增加了設備的靈活性；

The adjusting device of gasket-type outlet orifice is reliable and convenient, with a large adjusting range, which increases the flexibility of the machine; 

●排料口調整范圍大，可滿足不同用戶的要要求；設備節能：單機節能15%～30%，系統節能一倍以上；噪音低，粉塵少；

The adjustment range of outlet orifice is large, which can meet the requirements of different users; energy-saving equipment: The energy saving of a single machine is 15%-30%, and the system's energy saving is more than double of that; low noise and little dust. 

●潤滑系統安全可靠，部件更換方便，保養工作量小；結構簡單，工作可靠，運營費用低。

The lubrication system is safe and reliable, with convenient part replacement and little maintenance work; the structure is simple with a reliable performance low operating cost.

工作原理/ OPERATING PRINCIPLE

鄂式破碎機的工作部分由兩塊鄂板構成，固定鄂板（定鄂），垂直（或上端略外傾）固定在機體前壁上，另一個是活動鄂板（動鄂），位置傾斜，與固定鄂板形成上大下小的破碎腔（工作腔）。活動鄂板對著固定鄂板做周期性的往復運動，時而分開，時而靠近。分開時，物料進入破碎腔，成品從下部卸出；靠近時，使裝在兩塊鄂板之間的物料受到擠壓、彎折和劈裂作用而破碎。

The working parts of the Jaw Crusher consist of two jaw plates. The fixed jaw plate (fixed jaw) is fixed on the front wall of the machine body vertically (or the top tip slightly outward). The other is rotating jaw plate (rotating jaw), which is inclined in its position. And the two jaw plates form a crushing cavity (working cavity) with large top and small bottom. The rotating jaw plate is reciprocating periodically against the fixed jaw plate, sometimes separately and sometimes closely. When they are separated, the materials enter the crushing cavity, and the finished products are unloaded from the lower part; when they are approaching, the material loaded between the two jaw plates is crushed by the effects of extrusion, bending and splitting.